HUET Guide: Helicopter Underwater Escape Training & Egress Steps
Step-by-step preparation for Helicopter Underwater Escape Training, covering cabin orientation, physical reference points, and calm submerged egress.
Physics of a Helicopter Water Ditching
Unlike fixed-wing aircraft, helicopters carry heavy transmissions and rotor gearboxes mounted high above the cabin. When a helicopter makes an emergency water landing, wave impact or flotation failure frequently causes the fuselage to roll rapidly onto its side or invert 180 degrees within seconds.
In-rushing water, bubbles, and sudden darkness immediately disrupt inner-ear balance, making visual navigation unreliable. HUET trains passengers to rely on tactile reference points—a door frame, window sill, and seat buckle—rather than sight while executing a calm, sequenced escape.
- High center of gravity causes rapid inversion once water breaches cabin doors
- Turbid water and air bubbles erase up-versus-down visual cues
- Panic dramatically shortens breath-hold duration and increases entrapment risk
- Touch-based hand-over-hand navigation ensures reliable exit alignment
Pre-Impact Brace Position and Reference Points
Survival begins before water contact. Upon hearing the ditching command, passengers tighten lap and shoulder harnesses, secure loose gear, and adopt the cross-chest brace position with chin tucked toward the sternum and thumbs hooked beneath harness straps to protect the neck and keep arms from flailing.
Before impact, each occupant identifies a primary exit and an alternate exit across the cabin. Keeping one hand anchored on the window frame or seat edge throughout the roll prevents disorientation; if you do not release the buckle until the fuselage stops moving and all rotor blades come to rest, buoyancy will not pin you against the cabin ceiling.
Window Jettisoning and Sequenced Submerged Egress
Modern offshore helicopters use push-out acrylic windows bordered by pull-tab seals or corner strike points. During HUET simulator runs, trainees wait until cabin motion ceases, establish their outside reference hand on the sill, pull the jettison tab or strike the lower corner firmly, and confirm the exit is clear.
Only after the window is fully clear does the occupant release the four-point rotary buckle with their free hand, pull themselves horizontally through the frame using both hands along the sill, and swim upward toward surface light while following rising air bubbles. Pushing off gently rather than kicking wildly prevents kicking fellow passengers behind you.
- Wait for full cabin stop and violent water rush to subside before unbuckling
- Anchor outside hand firmly on the exit frame before touching the harness release
- Jettison window completely clear of the frame prior to releasing the seatbelt
- Pull through the aperture with arms first; inflate lifejacket only after surfacing
Progressive Simulator Runs in Pool Training
Quality HUET instruction builds confidence incrementally rather than overwhelming trainees on run one. Candidates begin with dry-cabin walkthroughs, advance to upright surface submersions, progress to partial rolls, and finish with full 180-degree inversions with emergency breathing equipment.
Between every dunker run, instructors debrief body mechanics, hand placement, and breath pacing. Trainees who slow down their hand movements by half a second typically exit faster and more cleanly than those who rush.
HUET Progressive Simulator Run Sequence
| Run Stage | Simulator Orientation | Breathing Mode | Primary Learning Objective |
|---|---|---|---|
| Stage 1: Dry Walk | Upright above water | Normal ambient air | Memorize brace position and rotary buckle release |
| Stage 2: Upright Sink | 0° upright submerged | Breath-hold | Practice reference hand and push-out window removal |
| Stage 3: 90° Roll | Side-roll partial invert | Breath-hold or EBS | Maintain spatial orientation during water in-rush |
| Stage 4: 180° Invert | Full upside-down roll | Breath-hold + EBS | Wait for motion stop before releasing 4-point harness |
| Stage 5: Cross-Cabin | 180° inverted blocked exit | CA-EBS / Rebreather | Reroute calmly to secondary exit across cabin |
Exact run counts vary by regulatory standard (Canadian CAOP, OPITO, or aviation operator requirements).
Worked Illustration: Four-Step Inverted Window Exit Sequence
This worked illustration traces the exact tactile sequence an offshore passenger executes inside an inverted HUET cabin when seated in a window seat.
- 1. Impact & Roll (0–4 sec): Maintain cross-chest brace until fuselage finishes rolling 180° and water fills the cabin; avoid unbuckling early so buoyancy does not float you away from the seat.
- 2. Reference & Jettison (4–7 sec): Slide outboard hand to the bottom edge of the window frame, grasp the pull-tab or strike the corner, and push the window cleanly outward.
- 3. Buckle Release (7–8 sec): With outboard hand still gripping the frame, rotate the central harness buckle 90° with the inboard hand and brush straps clear of the shoulders.
- 4. Horizontal Pull & Ascent (8–14 sec): Pull shoulders smoothly through the exit without inflating the lifejacket inside the cabin; follow bubbles to the surface, inflate PFD, and link up with crew.
Worked Illustration Result: Anchoring the reference hand before releasing the harness cuts disorientation and completes inverted egress in under 15 seconds.
HUET Student Preparation & In-Tank Checklist
- Remove rings, watches, hairpins, and eyeglasses before entering the simulator cabin.
- Fasten the four-point harness snugly across the hips and test the quick-release latch dry.
- Locate your primary window pull-tab and physically touch your secondary exit before every run.
- Never inflate your aviation lifejacket until your head and shoulders are clear on the water surface.
- Exhale small steady bubbles during ascent if breathing compressed air from a CA-EBS unit.
- Signal 'OK' to the pool safety diver immediately upon surfacing after each inversion.
Frequently Asked Questions
Why must you wait until the helicopter stops rolling before unbuckling?
Inside a submerged cabin, trapped air pockets and body buoyancy push you unpredictably toward the floor or ceiling. Staying strapped in keeps you anchored next to your known exit until motion stops.
Why is lifejacket inflation prohibited inside the cabin?
An inflated PFD creates strong upward buoyancy that can pin a passenger against the inverted cabin roof and prevent them from diving down through the submerged window opening.
What happens if my primary exit window is jammed or blocked?
HUET cross-cabin drills train you to keep one hand on your seat back, sweep across to the opposite side exit or aisle reference point, and egress through the nearest open aperture.
How long do trainees have to hold their breath during HUET?
Most unassisted inverted egress runs take only 8 to 15 seconds underwater, and instructors practice breath-control relaxation techniques before any submerged exercise begins.
Primary References & Standards
- International Association of Oil & Gas Producers (IOGP) — Report 690: Offshore Helicopter Recommended Practices
- Atlantic Canada Offshore Petroleum Training and Qualifications Committee — HUET & EBS Curriculum Standards
- Transport Canada — Aviation Occupational Health and Safety Regulations (SOR/2011-87)